| POWER SEQUENCERS |
| |
| MP-15 |
|
|
Features
of the Furman MP-15:
The MINIPORT-15 is equipped with two knockout holes for
permanent installation with 1/2" conduit — one on the
top surface, the other on the bottom. Use of the bottom
knockout hole requires removing the AC cord. According
to the National Electrical Code, 1/2" conduit can
accommodate up to five 20 amp circuits using ten THWN
12 gauge stranded wires; however, local codes should be
checked for exact requirements. MINIPORTs are housed in
rugged steel enclosures and come equipped with a heavy
duty, 10 foot AC cord. The MINIPORT-15 is fused
and UL and CUL (Canadian) listed.
|
| Model |
Description |
List
Price
|
Our
Price
|
| MP15F |
15 Amp Power Relay |
$129.00
|
|
Top
of Page
|
| MP-20 |
|
|
Features
of the Furman MP-20:
The MINIPORT-20 is equipped with two knockout holes for
permanent installation with 1/2" conduit — one on the top surface, the
other on the bottom. Use of the bottom knockout hole requires removing
the AC cord. According to the National Electrical Code, 1/2" conduit
can accommodate up to five 20 amp circuits using ten THWN 12 gauge
stranded wires; however, local codes should be checked for exact
requirements. MINIPORTs are housed in rugged steel enclosures and come
equipped with a heavy duty, 10 foot AC cord. The MINIPORT-20 is
equipped with a precision magnetic circuit breaker. The MINIPORT-20 is
UL and CUL (Canadian) listed.
|
| Model |
Description |
List
Price
|
Our
Price
|
| MP20F |
20 Amp Power Relay |
$179.00
|
|
Top
of Page
|
| MP-20Q |
|
|
Features
of the Furman MP-20Q:
The MINIPORT-20Q (20 amp), provide a pair of
remotely-activated, relay-controlled outlets, set up for mounting in
any standard electrical Quad Box, either directly or with a “mud ring”
attached. Due to the space limitations of a quad box, the “Q” models
have a smaller feature set than the MINIPORT-20. There is no internal
power supply; a maintained 10-30VDC supply capable of supplying 10 mA
is required to turn on the outlets. This can be supplied by a Furman
PowerLink, ASD-120, or PS-8R with a simple internal modification to the
PS-8R. UL, C-UL pending.
|
| Model |
Description |
List
Price
|
Our
Price
|
| MP20Q |
20 Amp Power Relay |
$110.00
|
|
Top of Page
|
| PS-8R II |
|
|
Features
of the Furman PS-8R II:
• SMP+ provides the
highest level of protection available •
LiFT significantly reduces AC line noise • E.V.S. protects
equipment from dangerous overvoltage conditions • Zero ground
contamination circuitry assures delivery of pure AC • Six sequenced rear
panel outlets (in 3 groups), two switched rear panel outlets, and one
front panel switched outlet • Momentary
and Maintained sequencing via rear panel terminal block or front panel
switch • 15
amp rating with circuit breaker •
BNC connector on the rear panel allows
connection of any standard gooseneck lamp •
Three year limited warranty
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| PS8RII |
Power Conditioner /
Sequencer |
$349.00
|
|
Top
of Page
|
| PS-REL |
|
|
Description
of the Furman PS-REL:
The PS-REL AC Relay provides an alternate way of closing
switch contacts. Instead of being operated manually like the RS-1, it
is a relay that detects the presence of AC power and, in response,
closes relay contacts that are wired to a terminal strip. It may be
used with any of the Furman products mentioned in connection with the
RS-1. A PS-REL is useful in determining when a certain outlet has come
on after a sequenced delay, to extend that outlet's capacity. It may
also be used to extend the capacity of the switched outlet found on
many home theater receiver/amps. In this way, a wireless remote can
turn on the receiver, which in turn powers its switched outlet, which
triggers the PS-REL, which then activates a Furman PS-8R or PS-PRO
Power Sequencer, MiniPort, or PowerPort system capable of switching
many large power amps or other power-hungry equipment in multiple
locations.
|
| Model |
Description |
List
Price
|
Our
Price
|
| PSREL |
AC Relay Accessory
for use with Sequencing Units |
$45.00
|
|
Top of Page
|
| PS-PRO II |
|
|
Features of
the Furman PS-PRO II:
• SMP+ provides the highest level
of protection available •
LiFT significantly reduces AC line noise •
E.V.S. protects equipment from dangerous overvoltage
conditions • Zero
ground contamination circuitry assures delivery of pure AC • Six sequenced rear
panel outlets (in 3 groups), two switched rear panel outlets, and one
front panel switched outlet •
Momentary and Maintained sequencing via rear panel terminal block or
front panel switch •
20 amp rating with circuit breaker • BNC connector on the
rear panel allows you to attach any standard 12V gooseneck lamp to
illuminate the rear of your rack •
Three year limited warranty
|
| Model |
Description |
List
Price
|
Our
Price
|
| PSPROII |
20 Amp Power Conditioner /
Sequencer |
$499.00
|
|
Top of Page
|
| POWERLINK |
|
|
Features
of the Furman PowerLink:
• Combines with up to six power
control devices to make a complete system to provide power-up and
power-down sequencing •
Actual PowerLink 'outputs' are electrically isolated, normally-closed
or normally-open relay contacts •
Each control output has a front panel status indicator • Each control output has
a three position switch allowing each connected device to be part of
the sequence, or to be switched on or off independently • On or off sequence can
be initiated from the unit or remotely, using low voltage control wires
•
Front panel key switch for security •
Compact single rack space package •
Three unswitched AC convenience outlets -- two on the rear
and one on the front
|
| Model |
Description |
List
Price
|
Our
Price
|
| POWERLINK |
Remote Sequence Controller |
$469.00
|
|
Top of Page
|
| POWERPORT |
|
|
Features
of the Furman PowerPort:
•
One PowerPort controls one 20 amp circuit - an unlimited number of
additional 20 amp circuits may be controlled by adding more PowerPorts • Turn-on or turn-off
sequence is initiated by a simple switch closure - switches may be
momentary or latching •
Can use multiple remote on-off switches for multi-location control • PRO-Series level spike
and surge clamping and EMI/RFI filtering provides the most
comprehensive power protection available anywhere! • High reliability 25 amp
relays •
Incoming mains voltage is monitored for acceptable levels, with
marginal voltages causing flashing alerts and extreme voltages causing
protective shutdown •
Manual mode allows delays to be overridden for troubleshooting • Screwdriver-adjustable
turn-on and turn-off delay times, each independently settable from 0 to
60 seconds •
Units may be wall-mounted or rack-mounted (half rack size) with
appropriate mounting kits
|
| Model |
Description |
List
Price
|
Our
Price
|
| POWERPORT |
Remote Power AC Power
Controller |
$410.00
|
|
| HRKIT1B |
Rackmount
Kit for Powerport |
$49.00 |
|
| PWRKIT1 |
Wall /
Under counter Mount Kit for (1) Powerport |
$69.00 |
|
| PWRKIT2 |
Rackmount
Kit for (2) Powerports |
$69.00 |
|
Top of Page
|
| RS-1 |
|
|
Features
of the Furman RS-1:
The RS-1 Remote System Control Panels provide a simple way
to control AC equipment from one or more locations, using only
inexpensive low-voltage wiring. The panels can be easily installed in a
single gang switchbox with a minimum depth of 1.5". Features common to
both models include a locking key switch and a “System On” indicator
LED. The RS-1 is a maintained contact version. The rear of the panels
have a circuit board with a full size barrier strip for field wiring
connections. The RS-1 and can be used to control the Furman ASD-120
Sequenced Power Distro, the PowerLink, PowerPort; Remote AC Controller,
the MiniPort Power Relay series, or the PS-8R or PS-PRO Power
Sequencers, as well as other equipment that needs a switch contact at a
remote location.
|
| Model |
Description |
List
Price
|
Our
Price
|
| RS1 |
Remote System Control Panel |
$45.00
|
|
Top of Page
|
| RS-2 |
|
|
Features
of the Furman RS-2:
The RS-2 Remote System Control Panels provide a simple way
to control AC equipment from one or more locations, using only
inexpensive low-voltage wiring. The panels can be easily installed in a
single gang switchbox with a minimum depth of 1.5". Features common to
both models include a locking key switch and a “System On” indicator
LED. The RS-2 includes a momentary “Start ON/OFF Sequence” pushbutton.
The rear of the panels have a circuit board with a full size barrier
strip for field wiring connections. The RS-2 can be used to control the
Furman ASD-120 Sequenced Power Distro, the PowerLink, PowerPort; Remote
AC Controller, the MiniPort Power Relay series, or the PS-8R or PS-PRO
Power Sequencers, as well as other equipment that needs a switch
contact at a remote location.
|
| Model |
Description |
List
Price
|
Our
Price
|
| RS2 |
Remote System Control Panel |
$45.00
|
|
Top
of Page
|
| AC POWER
DISTRIBUTION |
| |
| ACD-100 |
|
|
Features
of the Furman ACD-100:
• 100 amp total load • Five 20 amp, 120 volt
circuits, each with a status indicator •
Oversized buss bars • 4 buss design
accommodates 120V or 240V single phase, or 208V three phase power • High-inrush magnetic
circuit breakers • Varistor
spike and surge protection • Compact
two rack space package • Most
economical product of its type
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| ACD100 |
AC Power Distributor
- 100 Amp |
$649.00
|
|
Top
of Page
|
| ASD-120 |
|
|
Features
of the Furman ASD-120:
• 120 amp total load • Six 20 amp, 120 volt
circuits, each with a status indicator •
Oversized buss bars • Four buss design
accommodates 120V or 240V single phase, or 208V three phase power • Six widely spaced
duplex outlets on rear panel • Outlets
can be powered up and down in sequence •
Three position switch allows each circuit
to be part of the power sequencing, or to be switched on/off
independently • Sequence
timing can be initiated from unit or remotely, using low voltage
control wires • Sequence
control signals are available on rear panel to drive additional
ASD-120's or other devices and circuits •
Front panel key switch for security • Compact two rack space
package • Most
economical product of its type
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| ASD120 |
AC Sequencer / Distributor
- 120 Amp |
$799.00
|
|
Top
of Page
|
| IN-WALL SOLUTIONS |
| |
| MIW-XT |
|
|
Features
of the Furman MIW-XT:
•
Ultra-thin profile can allow equipment to
hang less than one inch from the wall •
EMI/RFI noise filtration built into outlet
receptacle • Power
and signal lines are hidden in the wall behind panel displays for a
clean, tidy and professional installation •
Extend Connected Equipment Policy to remote
equipment when used with Panamax/Furman Power Management components • Accommodates optional
MIW Signal Line Modules (sold separately, contact Panamax or Furman) • Compatible with most
standard electrical boxes • CSA
Certified for code compliant installations • Low profile flat plug
adapter cord. • Accomodates
optinal signal line/level modules, sold seperately. • Accomodates Decora and Keystone inserts (not
included) • compatible
with most standard electrical boxes • Mounting brackets and some installation
hardware is included. •
Utilizes a specially designed power cord/plug and securing clip to lock
power cord from component to receptacle. • 3 Year Product Warranty
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIWXT |
In-Wall
Power and Signal Line Cord Management Kit |
$149.95
|
|
Top
of Page
|
| MIW-POWER-PRO-PFP |
|
|
Features
of the Furman MIW-POWER-PRO-PFP:
• Two recessed AC
receptacles deliver power to remotely located devices. Enlarged
faceplate (4.5" x 4.5") accommodates oversized wall cutouts. Line fault
LED to indicate an overvoltage condition with the power to the
MIW-POWER -PRO-PFP. Power ON LED indicates power is being supplied to
the MIW-POWER-PRO-PFP outlets • Voltage monitoring Circuit
protects equipment against prolonged over voltages by disconnecting the
power and reconnecting it when safe power returns •
May be used in conjunction with MIW-DUAL-SIGNAL
BAY PFP and signal line modules (sold separately)
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIWPOWERPROPFP |
In-Wall Power Management
Faceplate |
$99.95
|
|
Top
of Page
|
| MIW-SURGE |
|
|
Features
of the Furman MIW-SURGE:
•
Provides surge protection • Ultra-thin profile can
allow equipment to hang less than one inch from the wall • Compatible with most
standard electrical boxes • Accommodates
optional installation solutions by using: Decora® Adapter,
Pass-Through Insert, Keystone 2-port adapter, MIW Signal Line Modules
(MIW modules sold separately) • CSA
Certified for code compliant installations • 3 Year Product Warranty
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIWSURGE |
In-Wall
Surge Protection System |
$69.95
|
|
Top
of Page
|
| MIW-VGA |
|
|
Features
of the Furman MIW-VGA:
• Low voltage module
for RGBHV • Connect
devices to 15 pin high-density D-sub connector on face of module • 3.5 mm stereo
mini-jack for 12 volt triggering and IR signal transmission • Use with MIW-POWER
family of products, such as the MIW-DUAL SIGNAL BAY
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIWVGA |
Low Voltage Module for
RGBHV |
$69.95
|
|
Top
of Page
|
| MIW-SVIDEO |
|
|
Features
of the Furman MIW-SVIDEO:
• Low voltage module
for video and/or audio, RCA jacks compatible with audio or video
signals • Use
with MIW-POWER family of products, such as the MIW-DUAL SIGNAL BAY
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIWSVIDEO |
Low Voltage
Module for Video and/or Audio |
$59.95
|
|
Top
of Page
|
| MIW-5RCA |
|
|
Features
of the Furman MIW-5RCA:
• Low voltage module
with 5 RCA connections • Use
with MIW-POWER
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIW5RCA |
Low Voltage Module with 5
RCA Connections |
$59.95
|
|
Top
of Page
|
| MIW-DATA |
|
|
Features
of the Furman MIW-DATA:
• Low voltage module
for projector control lines and/or computer data lines
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIWDATA |
Low Voltage Module for
Data Lines |
$59.95
|
|
Top
of Page
|
| MIW-DUAL SIGNAL
BAY |
|
|
Features
of the Furman MIW-DUAL SIGNAL BAY:
• MIW-DUAL SIGNAL BAY
provides a discreet and code compliant solution for a professional home
theater installation • 3
Year Product Warranty • May
be used in conjunction with MIW-POWER-PRO and signal line modules (sold
separately) • Accommodates
two blank module inserts with pass-through plugs (included) or two
In-Wall protection modules (sold separately) • Full metal housing • Enlarged faceplates
(4.5" x 4.5") to accommodate oversize wall cutouts • Fits into many
two-gang outlet brackets (old-work, low-voltage, Caddy-brand outlet
bracket model MPAL2 included) • 14
AWG, solid wire connection for bonding / grounding to In-Wall AC units • Provides an elegant,
convenient solution for connecting signal lines from the source device
to the display device when running cables within the building walls
|
|
| Model |
Description |
List
Price
|
Our
Price
|
| MIWDUALSIGNALBA |
Signal Bay for MIW
Modules |
$29.95
|
|
|
|
|
|
Nearest
Product Category | Other FURMAN
SOUND pages | Sales Home Page
Top of Page
|
